996 Turbo / GT2Turbo discussion on previous model 2000-2004 Porsche 911 Twin Turbo and 911 GT2. Sponsored By Vivid Racing
Welcome to 6SpeedOnline.com!
Welcome to 6SpeedOnline.com.
You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, join 6SpeedOnline.com today!
Scott, I've just been through this with my 19s. It was for my 3 inch piping with my new setup, not 335s. I spoke with Mark and Rhonda at FVD. They were very helpful. I'd recommend em. Also, I think Tial something or other had a pic of his car with 335s a few months ago. You could try searching for that thread. Hope it helps.
__________________ Something new is brewing....(insert monster laugh here)
Protomotive K24/18g 650 - gone but not forgotten
Scott, I've just been through this with my 19s. It was for my 3 inch piping with my new setup, not 335s. I spoke with Mark and Rhonda at FVD. They were very helpful. I'd recommend em. Also, I think Tial something or other had a pic of his car with 335s a few months ago. You could try searching for that thread. Hope it helps.
I'll look for the thread, thanks.
So...do they fit on your car? My piping might be in the way as well.
So...do they fit on your car? My piping might be in the way as well.
Well, we don't know yet. Markski is ovaling the 3 inch pipes (really cool) to gain more room and we won't have the spacers for my wheel until this Wed. They're out of the size I need and are coming from Germany. Part of the problem are my 305 tires. If it doesn't fit I'll either have to get 295s or go with my 996tt wheels with their different offsets.
I think your car has 3 inch pipes too. I sorta doubt you'll be able to get a 335 in there with that pipe from what I've seen.
__________________ Something new is brewing....(insert monster laugh here)
Protomotive K24/18g 650 - gone but not forgotten
Well, we don't know yet. Markski is ovaling the 3 inch pipes (really cool) to gain more room and we won't have the spacers for my wheel until this Wed. They're out of the size I need and are coming from Germany. Part of the problem are my 305 tires. If it doesn't fit I'll either have to get 295s or go with my 996tt wheels with their different offsets.
I think your car has 3 inch pipes too. I sorta doubt you'll be able to get a 335 in there with that pipe from what I've seen.
Got it.
I'm not sure if the offset on my HREs is the same as on your 997TT wheels. I guess I need to find out. Thanks.
When I went from the (19") 305/30 (I had rubbing) to the 315/25 I have more clearance on my TT. I think I could get the 325/25 in there with no mods or spacers. The profile and alignment have a big influence.
I bought some in anticipation; I have some spare 5 mm spacers if you need them
When I went from the (19") 305/30 (I had rubbing) to the 315/25 I have more clearance on my TT. I think I could get the 325/35 in there with no mods or spacers. The profile and alignment have a big influence.
I bought some in anticipacion; I have some spare 5 mm spacers if you need them
I had 12" GT2 wheels with stock 315s with 7mm spacers in rear with zero rubbing. Don't know if that helps.
My guess is yes.
__________________
My latest dyno chart 1.2 BAR: To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
2002 X50. Water cooled Tial GT2860RS, EVO Clubsport Intercoolers, Speedtech Y-Pipe (red), Boost Hoses, 60 lb Injectors, LWFW, RS Clutch, Remus Exhaust, DVs, GIAC FLASH To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. , 997 TT Brakes, FVD PSS9s, H&R Rear Bar, 19" Champion RG19 Monolites (15mm spacers front and rear), rollled fenders, ROTtec CF Lip and rear window spoiler, Strosek Wing.
Linear Mode
