991 DIYs
|
If anyone is interested in protecting their OEM front windshield from rock chips and cracks with a DIY kit, take a look at this thread: https://www.6speedonline.com/forums/...rotection.html
|
2 Attachment(s)
DIY - Radiator grill mesh
My front radiators started to look bad (no functional issue) and a fair amount of rubber and debris would accumulate in the radiator openings after each track day. https://www.6speedonline.com/forums/...ine=1366576170 There is no grill mesh option available on the market yet for the front sport apron, so I had to go for a quick DIY. I did not want to remove the front bumper, so I worked 'from the outside'. Step 1: created a model using painter's tape and semi-rigid wires https://www.6speedonline.com/forums/...ine=1366576170 Step 2: ordered grill mesh (12 x 48" small diamond - black) from customcargrills.com. I think you can find the same grill at your local Home Depot, but ordering online was more convenient and I trusted the quality a bit more. Step 3: use the model to cut grills for both radiators air intakes https://www.6speedonline.com/forums/...ine=1366576170 Step 4: just slide the grill in and attach with 4 zip ties https://www.6speedonline.com/forums/...ine=1366576170 ... and here's the final result: https://www.6speedonline.com/forums/...ine=1366576170 https://www.6speedonline.com/forums/...ine=1366576170 edit: I have attached a PDF file with the template to be used for the grills. |
BMC air filter
Here we go again with a +0.5 hp/+0.5 dB mod. What is the point of being sarcastic since it is the SECOND time that I do this mod on a 991 :o ? First, I like mods that I can do myself, second, even if the benefit can hardly be quantified, it can do no harm and you have a (little) bit more sound. You will need to remove the rear bumper to get access to the airbox. To do this, you'll have to lift/jack the back of the car so that you can remove both wheels. https://www.6speedonline.com/forums/...ine=1367294652r You will get access to the top screws by lifting the wing (if powered or by removing the 2 screws under the engine lid and popping out the ducktail/fixed wing). Just do not rush things and check that you are not forgetting any screws. You will first remove the taillights, then go around the bumper and remove all the screws you see. Do not forget the 3 screws in each wheel arch. When you are ready to remove the bumper, pull gently and make sure you do not tear off the license plate lighting power cable. https://www.6speedonline.com/forums/...ine=1367294652 Open the air box, swap the filters and reassemble. Stock filters: https://www.6speedonline.com/forums/...ine=1367294652 BMC filters: https://www.6speedonline.com/forums/...ine=1367294652 Be patient again when you put the bumper back in place, you want to make sure that it remains well aligned and flush with the body of the car. Done in 60 to 75 minutes in total. Enjoy! |
A little more on deconstructing your 991 to install a BMC air filter or just change the OE one. No way to do it without dropping the rear bumper.
http://www.youtube.com/watch?v=Rnfp6...ature=youtu.be |
Cabin Air Filter
|
I can't believe with the rear bumper off you still can not see the engine! They really did a good job of hiding it on the 991.
|
You will need to remove the rear bumper to get access to the airboxhttp://www.glpp.info/hu6e.jpg
|
My driver side window switch wasn't functioning properly. It would lower and raise if I held the switch in position, but it would not go up or down all the way when I hit auto. The dealership gave me instructions on resetting the window switch. It fixed the problem, and I thought I'd pass it along.To reset (car must be on):1) lower the window all the way down and release the switch2) push the switch down, hold it there for 3 seconds, and then release3) raise the window all the way and release the switch4) pull the switch up, hold it for 3 seconds, and then release5) turn car off and then back onHope this helps anyone else who is having switch problems.*Alex
|
DIY Mesh for front grills
6 Attachment(s)
I checked the reference above, but that's for the sport bumper cap. Since I have the regular front end I also made my own. I ordered the mesh from customcargrills and made a cardboard template to the rough shape of the opening. I bent the mesh around a 1" pipe and slid it into the opening. Once it was all the way in, there is plenty of room to slide it to one side and get my hand behind the mesh and straighten out the bend. Then slide it the opposite side and finish bending the mesh straight. Then with a couple of black tie wraps to the vertical supports (on the bottom sides) and one on the outboard end and I was done.
PS, excuse all the bugs, I just got back from a fantastic 3 day drive with 5 other Porsche owners to find my intakes full of bugs, leaves and stones. No time like the present to get this mod done. |
Resetting Window
|
|
DIY "Quiet Cabin" Mod. (Locating/blocking the sound symposer valve that pipes in intake/engine noise).
https://www.6speedonline.com/forums/...poser-mod.html |
|
Great detailing tips and recommended product tips
https://www.6speedonline.com/forums/...etailings.html |
All times are GMT -6. The time now is 09:45 PM. |
© 2024 MH Sub I, LLC dba Internet Brands