991 PCM 3.1 Removal - Part 2
This is the second part DIY for removing the PCM 3.1 unit from the dash of a '14 991 C4S.
Visit Part 1 if you need to remove the right and left side trim pieces.... In previous steps, we've removed the two console trim pieces. Here I've indicated all of the female receptacles in the console that the trim piece connects-to: https://cimg0.ibsrv.net/gimg/www.6sp...3de09c8233.jpg https://cimg1.ibsrv.net/gimg/www.6sp...a0766e50b1.jpg In this pic I indicate the slot where the "hook-tab" connects - you don't want to break this one off (see further down for a pic of the tab)! https://cimg2.ibsrv.net/gimg/www.6sp...bec046a360.jpg Here's a pic of the passenger side trim piece removed: https://cimg3.ibsrv.net/gimg/www.6sp...199296128a.jpg And in these shots I circled all the little tension tabs on the reverse side of each piece. There are a lot of them! https://cimg6.ibsrv.net/gimg/www.6sp...b2e957375b.jpg https://cimg7.ibsrv.net/gimg/www.6sp...63482a83ad.jpg There is one tab that is really fragile, and it is more of a "hook" tab that has to clamp into its' connection point under the dash - here is a pic highlighting this tab... Also, note at the top there is a tab that simply insert straight-ahead into the console next to the PCM unit in the dash. https://cimg8.ibsrv.net/gimg/www.6sp...d12f9f5aae.jpg With the trim panels removed, you have now exposed the PCM unit screws to each side of the PCM unit. Indicated in this pic are the 4 T-25 screws that you need to remove from the PCM unit to get it out of the dash: https://cimg0.ibsrv.net/gimg/www.6sp...ccd4a177cb.jpg And here are close-ups of the right / left side screws (I also indicate the hole where one of the trim piece tabs inserts straight-forward) https://cimg1.ibsrv.net/gimg/www.6sp...f27651da6f.jpg https://cimg3.ibsrv.net/gimg/www.6sp...4fd8d25fa8.jpg Cover the area directly below the PCM unit, and move the gear selector back https://cimg9.ibsrv.net/gimg/www.6sp...d04773f610.jpg Remove the screws... https://cimg0.ibsrv.net/gimg/www.6sp...11f859c289.jpg Gently pull the unit out of the dash https://cimg1.ibsrv.net/gimg/www.6sp...422fa9d3fe.jpg When you have the unit out far enough to reach the cables in the rear of the unit, you will want to disconnect everything. Be CAREFUL how you remove the connectors -- if you pull too hard on the wires you can pull them out of the connector module! So gently work the connectors out. Here are some pics of the rear of the PCM unit (I've circled the wire bundle that you want to focus-on for integrating something like the NAV-TV plug-and-play harness....) https://cimg1.ibsrv.net/gimg/www.6sp...57b95c9b59.jpg https://cimg2.ibsrv.net/gimg/www.6sp...b1d1a2f266.jpg https://cimg3.ibsrv.net/gimg/www.6sp...564a64174b.jpg https://cimg4.ibsrv.net/gimg/www.6sp...f08ddc9ef1.jpg If you are adding a different NAV-TV connector, like the RGB3.1 or the AV970 kits, you will have to remove the unit entirely so that you can put it on a bench and open the case. Unless you have to I would avoid breaking the warranty seals on the unit until after warranty period ends. You don't want any problems you have before then to be blamed on your modification! Interestingly, I was expecting a large warning label about voiding warranty, but all I found was this little white label... https://cimg8.ibsrv.net/gimg/www.6sp...97e51ecce4.jpg That's it for now! I don't have the NAV-TV unit yet to actually connect everything, but I will soon and will put together another DIY showing the process of making the connections, and wiring-up a camera from the rear. To put everything back the way it was, simply reverse the steps above! For previous steps, Go To Part 1. |
Will be waiting on the DIY on the camera install :D
Thank you again jawells1 |
Thank you jawells1, that was outstanding. I too am looking forward to seeing the camera install.
BTW did you install the wood trim or was that from the factory? ChuckJ |
AWESOME stuff!! Thanks!
|
Originally Posted by ChuckJ
(Post 4185840)
Thank you jawells1, that was outstanding. I too am looking forward to seeing the camera install.
BTW did you install the wood trim or was that from the factory? ChuckJ The wood trim was a factory option, Mahogany intertior trim. |
Unbelievable instructions! Great job.
|
How can this man only have 16 rep points???
Come on people, show the man some love for his tireless efforts and endless DIY contributions. |
Originally Posted by dux
(Post 4187948)
How can this man only have 16 rep points???
Come on people, show the man some love for his tireless efforts and endless DIY contributions. |
GREAT DIY! Thank you! and I am waiting for more!
|
USB Port in glove
Does swapping the head unit, provide a USB port in the glove box as well?
|
I wonder if we can switch out the 991.1 head unit and replace it with the larger 991.2 head unit??
|
991 PCM 3.1 Removal - Part 2
Originally Posted by PorscheCrazy
I wonder if we can switch out the 991.1 head unit and replace it with the larger 991.2 head unit??
That's the single most important update of the 991.2 that appeals to me. |
All times are GMT -6. The time now is 10:52 AM. |
© 2024 MH Sub I, LLC dba Internet Brands