6SpeedOnline - Porsche Forum and Luxury Car Resource
Here is the picture from the Ebay ad. These are pretty cars!
Here is the picture from the Ebay ad. These are pretty cars!
0 2019/03/16 18:22:41
One of the few tools I had to fabricate. The E-Brake to backing plate springs are too narrow to just use a hose clamp so I took some shim stock and made a release tool. Cheaper than the $120 from AM.
One of the few tools I had to fabricate. The E-Brake to backing plate springs are too narrow to just use a hose clamp so I took some shim stock and made a release tool. Cheaper than the $120 from AM.
0 2019/03/16 18:22:44
I built a couple of work frames from 4 furniture dolleys and 4X4s.
I built a couple of work frames from 4 furniture dolleys and 4X4s.
0 2019/03/16 18:22:46
I only have a 8' garage, so a MaxJax 6 is all I can fit. It's sufficient to bring the car up and out of the way. I'll need to go up some more to wheel the assembly out.
I only have a 8' garage, so a MaxJax 6 is all I can fit. It's sufficient to bring the car up and out of the way. I'll need to go up some more to wheel the assembly out.
0 2019/03/16 18:22:48
0 2019/03/24 15:22:34
scuzzy big end crank
scuzzy big end crank
0 2019/03/30 13:21:06
block with crank, mains still attached
block with crank, mains still attached
0 2019/03/30 13:21:08
homemade spread tool using a turnbuckle
homemade spread tool using a turnbuckle
0 2019/03/30 13:21:10
most of the big end plan bearings from #3 & #9 rods ended up in the bottom of the pan
most of the big end plan bearings from #3 & #9 rods ended up in the bottom of the pan
0 2019/03/30 13:21:12
0 2019/08/17 10:48:42
0 2019/08/17 10:48:48
0 2019/08/17 10:48:54
front of motor - note steering gear and sway bar
front of motor - note steering gear and sway bar
0 2019/08/18 15:42:25
RHS looking back to where the K frame mounts to subframe.
RHS looking back to where the K frame mounts to subframe.
0 2019/08/18 15:42:33
0 2019/09/21 16:09:42
0 2019/09/21 16:09:47
honed the journals and caps
honed the journals and caps
0 2019/10/30 15:21:47
all done!
all done!
0 2019/10/30 15:21:51
48 valve seats cut!
48 valve seats cut!
0 2019/10/30 15:21:54
0 2019/11/23 17:46:48
0 2019/12/06 15:34:09
0 2019/12/06 15:34:17
0 2019/12/21 06:33:24
0 2019/12/21 06:33:44
0 2019/12/28 18:09:11
0 2019/12/28 18:09:19
0 2019/12/30 14:53:04
0 2019/12/30 14:54:15
0 2019/12/30 14:54:29
0 2019/12/30 14:54:45
0 2020/01/02 18:24:04
0 2020/01/02 18:24:10
0 2020/01/03 13:39:25
0 2020/01/03 13:39:32
0 2020/01/03 13:39:39
0 2020/01/05 18:07:20
Really, it will fit!
Really, it will fit!
0 2020/01/11 19:28:43
The high pressure hose goes in front of the return line, which mounts to the bottom of the left front "horn".
The high pressure hose goes in front of the return line, which mounts to the bottom of the left front "horn".
0 2020/01/11 19:28:51
0 2020/01/12 09:14:01
0 2020/01/12 09:14:08