6SpeedOnline - Porsche Forum and Luxury Car Resource
Somewhat different spinning wheel pic ;-)
Somewhat different spinning wheel pic ;-)
0 2015/01/09 04:32:25
0 2015/01/18 12:58:10
0 2015/02/04 17:02:11
0 2015/02/20 22:47:14
Overview of everything. Rails, baskets, fittings, and wiring to connect into the stock harness.
Overview of everything. Rails, baskets, fittings, and wiring to connect into the stock harness.
0 2015/03/02 14:32:49
Close up of one of the rails, it's a work of CNC art!
Close up of one of the rails, it's a work of CNC art!
0 2015/03/02 14:33:35
Top plate with vent showing the MILspec wiring connector.
Top plate with vent showing the MILspec wiring connector.
0 2015/03/02 14:34:14
Bottom of the top plate, return fittings, Wiring, and fuel pump plumbing.
Bottom of the top plate, return fittings, Wiring, and fuel pump plumbing.
0 2015/03/02 14:35:30
More art! Check out the pump holders, wow!
More art! Check out the pump holders, wow!
0 2015/03/02 14:36:22
Pump holder again, complex and very well built!
Pump holder again, complex and very well built!
0 2015/03/02 14:37:21
wiring connections. The round one is MILspec pinned connection, the other is a 3D printed connector with some really nice heat shrink sealing it up for connection to the stock harness.
wiring connections. The round one is MILspec pinned connection, the other is a 3D printed connector with some really nice heat shrink sealing it up for connection to the stock harness.
0 2015/03/02 14:38:15
0 2015/04/04 15:35:12
0 2015/04/04 15:35:54
0 2015/04/04 19:10:55
0 2015/04/04 19:11:19
0 2015/04/15 15:49:28
0 2015/04/15 15:49:49
0 2015/05/16 07:40:58
0 2015/05/16 10:57:29
0 2015/07/27 21:49:39
Passenger side installed with temp probes!
Passenger side installed with temp probes!
0 2015/09/06 19:36:51
Driver's side installed!
Driver's side installed!
0 2015/09/06 19:39:20
Picasso with fiberglass I'm not!
Picasso with fiberglass I'm not!
0 2015/09/06 19:43:43
Rough it up before 'glassing!
Rough it up before 'glassing!
0 2015/09/06 19:44:17
Rough the rivets too :)
Rough the rivets too :)
0 2015/09/06 19:44:48
Cut with a hacksaw SLOWLY! Draw a line using a short drinking glass with a Sharpie laid across it. I cut just above the vinyl plug in the duct. Draw a vertical line to help orient the cut..
Cut with a hacksaw SLOWLY! Draw a line using a short drinking glass with a Sharpie laid across it. I cut just above the vinyl plug in the duct. Draw a vertical line to help orient the cut..
0 2015/09/06 19:45:15
Top edge of gasket supported with a strip of plastic cut to fit!
Top edge of gasket supported with a strip of plastic cut to fit!
0 2015/09/06 19:54:18
Clips installed! By the time you do the second set it goes much more quickly.
Clips installed! By the time you do the second set it goes much more quickly.
0 2015/09/06 20:01:13
Hard to see it but the gold nut holds the strip. This was the side done with too much clearance, you can do better!
Hard to see it but the gold nut holds the strip. This was the side done with too much clearance, you can do better!
0 2015/09/06 20:16:18
0 2015/09/27 13:22:58
0 2015/12/06 13:26:24
Hopefully this comes out.
Hopefully this comes out.
0 2015/12/27 20:48:27
0 2016/07/05 22:59:41
0 2016/09/11 21:43:59
0 2016/11/07 19:05:38
Side view, note it follows the form of the stock piece - it's nearly a direct bolt-on as a result!
Side view, note it follows the form of the stock piece - it's nearly a direct bolt-on as a result!
0 2017/02/20 19:46:24
Gotta have a logo somewhere on it!
Gotta have a logo somewhere on it!
0 2017/02/20 19:46:55
This is the part that will stick through the firewall. I'll talk more about it when I discuss the install!
This is the part that will stick through the firewall. I'll talk more about it when I discuss the install!
0 2017/02/20 19:48:04
Clutch clevis turned and polished. I didn't have to remove much but DO test this before installing the master!
Clutch clevis turned and polished. I didn't have to remove much but DO test this before installing the master!
0 2017/02/20 20:34:26
You want this gold bracket out, you can see the grommet on the green pressure hose and the black nipple for the reservoir feed.
You want this gold bracket out, you can see the grommet on the green pressure hose and the black nipple for the reservoir feed.
0 2017/02/20 20:41:58