6SpeedOnline - Porsche Forum and Luxury Car Resource
Canadians should buy this. Princess auto $99..... complete tester
Canadians should buy this. Princess auto $99..... complete tester
0 2015/07/06 20:57:18
0 2015/11/05 10:05:56
0 2015/11/07 11:08:22
0 2015/11/08 13:21:00
0 2015/11/11 15:40:20
0 2015/11/11 15:40:24
0 2015/11/11 15:40:26
0 2015/11/12 06:44:47
0 2015/11/14 13:18:32
0 2015/11/17 18:07:45
0 2015/12/12 10:18:01
0 2015/12/12 10:20:41
0 2015/12/22 06:36:34
0 2015/12/22 06:36:35
0 2015/12/22 06:36:36
SRM 10-12 mm head stud adapter kit
SRM 10-12 mm head stud adapter kit
0 2015/12/28 20:07:43
Align tool with 10 mm hole alignment pin.
Align tool with 10 mm hole alignment pin.
0 2015/12/28 20:09:10
Remove alignment pin and insert drill bit guide into tool. (drill bit tip has been removed to stop the bit from digging past the bottom of the existing hole)
Remove alignment pin and insert drill bit guide into tool. (drill bit tip has been removed to stop the bit from digging past the bottom of the existing hole)
0 2015/12/28 20:09:49
Remove drill bit and bit guide and insert the tap guide. (I used WD40 on the tap and hole). Tap hole until the bit bottoms out.
Remove drill bit and bit guide and insert the tap guide. (I used WD40 on the tap and hole). Tap hole until the bit bottoms out.
0 2015/12/28 20:10:54
Enjoy your newly installed 12 mm stud.
Enjoy your newly installed 12 mm stud.
0 2015/12/28 20:13:17
Cut an existing 10 mm head stud to use to fasten the tool to the case.
Cut an existing 10 mm head stud to use to fasten the tool to the case.
0 2015/12/28 20:13:55
0 2015/12/28 20:14:51
I had to remove the timing chains covers to get to the inside holes as the drill I had would not clear the chain covers. If you had an angle drill or really small drill you wouldn't have to do this.
I had to remove the timing chains covers to get to the inside holes as the drill I had would not clear the chain covers. If you had an angle drill or really small drill you wouldn't have to do this.
0 2015/12/28 20:15:08
0 2015/12/30 18:12:14
0 2016/01/10 11:14:48
Here's mine.
Here's mine.
0 2016/01/23 09:23:48
0 2016/01/24 15:59:37
Easier to just go on proto's dyno?
Easier to just go on proto's dyno?
0 2016/02/07 16:29:16
0 2016/02/29 12:00:20
0 2016/03/02 05:53:38
0 2016/03/02 05:53:50
0 2016/03/02 05:53:54
0 2016/03/02 05:53:58
0 2016/03/02 05:54:02
0 2016/03/02 05:54:05
0 2016/03/02 05:54:08
0 2016/03/02 05:54:10
0 2016/03/02 05:54:13
0 2016/03/04 06:13:09
0 2016/03/09 17:21:48