6SpeedOnline - Porsche Forum and Luxury Car Resource
0 2018/01/06 03:11:53
It’s hiding under the corner and you can remove the air pipe easily to pull it out after snipping a tie wrap The cover plate on top of the rad comes off easily New tails to 1+2
It’s hiding under the corner and you can remove the air pipe easily to pull it out after snipping a tie wrap The cover plate on top of the rad comes off easily New tails to 1+2
0 2018/04/21 04:32:27
RHS ( looking back ) bit easier to get at .New tails to 1+2
RHS ( looking back ) bit easier to get at .New tails to 1+2
0 2018/04/21 04:32:35
Just taped over the wires and tie wrapped up away from the fan and poly belt .
Just taped over the wires and tie wrapped up away from the fan and poly belt .
0 2018/04/21 04:32:43
0 2018/10/29 05:52:54
0 2018/10/29 05:52:55
0 2018/10/29 05:52:55
0 2018/10/29 05:52:57
0 2018/10/29 06:00:27
Before see the gap ?
Before see the gap ?
0 2018/10/29 06:01:52
Before see the gap RHS just keeps unpopping
Before see the gap RHS just keeps unpopping
0 2018/10/29 06:05:51
Cover off ,came off easy once you know how Lower LHS # clip holder ,not the cause here .
Cover off ,came off easy once you know how Lower LHS # clip holder ,not the cause here .
0 2018/10/29 06:05:53
Done gap normal / gone
Done gap normal / gone
0 2018/10/29 06:05:54
It was a loose clip I thightened them up , pressed the edges together and squeezed the rear bit closer so it would grip more .You can test on the panal while it’s out before refitted to test the grip
It was a loose clip I thightened them up , pressed the edges together and squeezed the rear bit closer so it would grip more .You can test on the panal while it’s out before refitted to test the grip
0 2018/10/29 06:05:55
Johnny’s pics from his rebuild thread Yours shouldn’t be rusty
Johnny’s pics from his rebuild thread Yours shouldn’t be rusty
0 2018/11/24 03:32:55
Johnny s pics from his restore thread
Johnny s pics from his restore thread
0 2018/11/24 03:32:55
The other torx for the corner visible once the main trim is loose
The other torx for the corner visible once the main trim is loose
0 2018/11/24 03:32:57
Then slide it forwards .You can see here how it unlocks once 2 cm forwards .It can then be swung out enough to access further in
Then slide it forwards .You can see here how it unlocks once 2 cm forwards .It can then be swung out enough to access further in
0 2018/11/24 03:32:57
The rear torx for the corner piece ( excuse the mirror )
The rear torx for the corner piece ( excuse the mirror )
0 2018/11/24 03:32:57
0 2019/01/16 11:48:44
This is a piece of fireproof sheeting tie wrapped over the main fuse / relay box to protect from water .A personal mod I did .
This is a piece of fireproof sheeting tie wrapped over the main fuse / relay box to protect from water .A personal mod I did .
0 2019/04/16 07:39:24
0 2019/01/16 11:48:45
0 2019/01/16 12:02:42
0 2019/04/16 07:39:29
My HVAC unit - note the “ splice “ and multi pin sockets I think moved up from under the unit . A previous repair / mod from the previous owner .
My HVAC unit - note the “ splice “ and multi pin sockets I think moved up from under the unit . A previous repair / mod from the previous owner .
0 2019/04/16 07:39:34
Other side .
Other side .
0 2019/04/16 07:39:39
Try in there as well
Try in there as well
0 2019/04/16 07:39:44
Other side of the HVAC “ bulkhead “ Also not shown the opposite side and carefully vac up everything.
Other side of the HVAC “ bulkhead “ Also not shown the opposite side and carefully vac up everything.
0 2019/04/16 07:39:49
Attached to the end of a vacuum cleaner and inserted to the side of the HVAC and crucially rotated 90 degrees to get right under towards the drain opening .
Attached to the end of a vacuum cleaner and inserted to the side of the HVAC and crucially rotated 90 degrees to get right under towards the drain opening .
0 2019/04/16 07:39:53
When down showing how you twist it 90 degrees .
When down showing how you twist it 90 degrees .
0 2019/04/16 07:39:58
Vac adapter.
Vac adapter.
0 2019/04/16 07:40:02
Cup full of water added .You can hear it instantly trickle on the floor .
Cup full of water added .You can hear it instantly trickle on the floor .
0 2019/04/16 07:40:07
Results.Free flowing .
Results.Free flowing .
0 2019/04/16 07:40:11
Set wipers to service and mark on the screen with tape .Helps realignment.
Set wipers to service and mark on the screen with tape .Helps realignment.
0 2019/04/16 07:40:16
14 mm ratchet remove them .If they have not been off for a while this may need a bit of penetrating oil and twiddling.Use something like copperslip when you put them back
14 mm ratchet remove them .If they have not been off for a while this may need a bit of penetrating oil and twiddling.Use something like copperslip when you put them back
0 2019/04/16 07:40:20
Turn the clips and prise the cover off the engine bulkhead .There May be a couple of screws to remove at the ends near the glass as well.
Turn the clips and prise the cover off the engine bulkhead .There May be a couple of screws to remove at the ends near the glass as well.
0 2019/04/16 07:40:26
Look carefully what’s lying at the bottom , running through.I suspect it’s an aftermarket mod to run that wire off the scuttle floor which is under that unit
Look carefully what’s lying at the bottom , running through.I suspect it’s an aftermarket mod to run that wire off the scuttle floor which is under that unit
0 2019/04/27 01:13:34
The red dot is amazing, actually allows water to drip / flood the fuse box lid !! - how ridiculous?
The red dot is amazing, actually allows water to drip / flood the fuse box lid !! - how ridiculous?
0 2019/04/27 01:13:38
Standing water
Standing water
0 2019/04/27 08:17:08
Rain and beech tree leave unfurling and spreading with wind sticking to the glass .
Rain and beech tree leave unfurling and spreading with wind sticking to the glass .
0 2019/04/27 08:17:12