6SpeedOnline - Porsche Forum and Luxury Car Resource
with flash :)
with flash :)
0 2017/04/23 13:36:05
Complete! Hazard and microphone installed, it all works too! Whew!
Complete! Hazard and microphone installed, it all works too! Whew!
0 2017/04/23 13:35:27
Gauges added, looking good!
Gauges added, looking good!
0 2017/04/23 13:35:00
Pulled apart and gauge pod removed - an impressive number of screws to get to this point!
Pulled apart and gauge pod removed - an impressive number of screws to get to this point!
0 2017/04/23 13:34:23
Stock! Rings are OEM Porsche :)
Stock! Rings are OEM Porsche :)
0 2017/04/23 13:33:42
Stubby plastic hose removed from the OEM master
Stubby plastic hose removed from the OEM master
0 2017/02/22 20:57:31
Both hoses attached, piano wire clip through the billet to hold the green pressure hose. Grommet not yet installed on my car d'oh!
Both hoses attached, piano wire clip through the billet to hold the green pressure hose. Grommet not yet installed on my car d'oh!
0 2017/02/20 22:15:50
Plastic hose from the top of the OEM master cylinder
Plastic hose from the top of the OEM master cylinder
0 2017/02/20 22:13:41
0 2017/02/20 20:48:08
Not the clip in question but the other is identical!
Not the clip in question but the other is identical!
0 2017/02/20 20:46:55
You want this gold bracket out, you can see the grommet on the green pressure hose and the black nipple for the reservoir feed.
You want this gold bracket out, you can see the grommet on the green pressure hose and the black nipple for the reservoir feed.
0 2017/02/20 20:41:58
Clutch clevis turned and polished. I didn't have to remove much but DO test this before installing the master!
Clutch clevis turned and polished. I didn't have to remove much but DO test this before installing the master!
0 2017/02/20 20:34:26
This is the part that will stick through the firewall. I'll talk more about it when I discuss the install!
This is the part that will stick through the firewall. I'll talk more about it when I discuss the install!
0 2017/02/20 19:48:04
Gotta have a logo somewhere on it!
Gotta have a logo somewhere on it!
0 2017/02/20 19:46:55
Side view, note it follows the form of the stock piece - it's nearly a direct bolt-on as a result!
Side view, note it follows the form of the stock piece - it's nearly a direct bolt-on as a result!
0 2017/02/20 19:46:24
0 2016/11/07 19:05:38
0 2016/09/11 21:43:59
0 2016/07/05 22:59:41
Hopefully this comes out.
Hopefully this comes out.
0 2015/12/27 20:48:27
0 2015/12/06 13:26:24
0 2015/09/27 13:22:58
Hard to see it but the gold nut holds the strip. This was the side done with too much clearance, you can do better!
Hard to see it but the gold nut holds the strip. This was the side done with too much clearance, you can do better!
0 2015/09/06 20:16:18
Clips installed! By the time you do the second set it goes much more quickly.
Clips installed! By the time you do the second set it goes much more quickly.
0 2015/09/06 20:01:13
Top edge of gasket supported with a strip of plastic cut to fit!
Top edge of gasket supported with a strip of plastic cut to fit!
0 2015/09/06 19:54:18
Cut with a hacksaw SLOWLY! Draw a line using a short drinking glass with a Sharpie laid across it. I cut just above the vinyl plug in the duct. Draw a vertical line to help orient the cut..
Cut with a hacksaw SLOWLY! Draw a line using a short drinking glass with a Sharpie laid across it. I cut just above the vinyl plug in the duct. Draw a vertical line to help orient the cut..
0 2015/09/06 19:45:15
Rough the rivets too :)
Rough the rivets too :)
0 2015/09/06 19:44:48
Rough it up before 'glassing!
Rough it up before 'glassing!
0 2015/09/06 19:44:17
Picasso with fiberglass I'm not!
Picasso with fiberglass I'm not!
0 2015/09/06 19:43:43
Driver's side installed!
Driver's side installed!
0 2015/09/06 19:39:20
Passenger side installed with temp probes!
Passenger side installed with temp probes!
0 2015/09/06 19:36:51
0 2015/07/27 21:49:39
0 2015/05/16 10:57:29
0 2015/05/16 07:40:58
0 2015/04/15 15:49:49
0 2015/04/15 15:49:28
0 2015/04/04 19:11:19
0 2015/04/04 19:10:55
0 2015/04/04 15:35:54
0 2015/04/04 15:35:12
wiring connections. The round one is MILspec pinned connection, the other is a 3D printed connector with some really nice heat shrink sealing it up for connection to the stock harness.
wiring connections. The round one is MILspec pinned connection, the other is a 3D printed connector with some really nice heat shrink sealing it up for connection to the stock harness.
0 2015/03/02 14:38:15