6SpeedOnline - Porsche Forum and Luxury Car Resource
Share Your Pictures with Our Community. Upload Now
0 2017/09/01 14:12:24
0 2017/09/01 14:12:21
0 2017/09/01 14:12:18
0 2017/09/01 13:19:42
0 2017/09/01 13:19:11
0 2017/09/01 13:18:54
0 2017/09/01 12:03:38
0 2017/09/01 12:03:32
0 2017/09/01 10:33:14
0 2017/09/01 09:24:51
0 2017/09/01 09:16:04
0 2017/09/01 08:58:07
Advertisement
0 2017/09/01 08:56:23
0 2017/09/01 08:54:40
Engine Bay 9-1-17
Engine Bay 9-1-17
0 2017/09/01 08:45:50
0 2017/09/01 05:27:15
0 2017/09/01 05:26:25
0 2017/09/01 05:26:10
0 2017/09/01 05:19:19
0 2017/09/01 05:19:05
0 2017/08/31 21:00:13
0 2017/08/31 20:59:30
0 2017/08/31 20:58:41
0 2017/08/31 20:58:09
Tweeter installed in side dash opening.
Tweeter installed in side dash opening.
0 2017/08/31 20:42:20
I then wrapped the circumference of the tweeter with thin silicone adhesive weatherstripping so that once I squeezed it into the clips it would be held securely and not vibrate or rattle.
I then wrapped the circumference of the tweeter with thin silicone adhesive weatherstripping so that once I squeezed it into the clips it would be held securely and not vibrate or rattle.
0 2017/08/31 20:42:09
Rubber spacer adhered into side tweeter opening
Rubber spacer adhered into side tweeter opening
0 2017/08/31 20:42:05
Wanted to do something similar on the 2 side tweeters to keep them from being too low in the cavities. These rubber pieces I had fit the bill perfectly - don't know what they came from. I did the same thing with the 3M trim tape on the bottom side.
Wanted to do something similar on the 2 side tweeters to keep them from being too low in the cavities. These rubber pieces I had fit the bill perfectly - don't know what they came from. I did the same thing with the 3M trim tape on the bottom side.
0 2017/08/31 20:41:59
Tweeter installed in center hole. Wires are from the sensor on the speaker cover.
Tweeter installed in center hole. Wires are from the sensor on the speaker cover.
0 2017/08/31 20:41:54
In looking into the speaker cavity, there is a section that has a bottom support. I used some 3M trim tape in the corresponding position of the rubber stopper and adhered the bottom of the stopper to this support.
In looking into the speaker cavity, there is a section that has a bottom support. I used some 3M trim tape in the corresponding position of the rubber stopper and adhered the bottom of the stopper to this support.
0 2017/08/31 20:41:47
Fully assembled tweeter on the mount
Fully assembled tweeter on the mount
0 2017/08/31 20:41:42
Once I removed the OEM center speaker, I realized it was in a fairly deep hole. Tweeters sound best when they're as far up as possible so I didn't want to just set the tweeter in the bottom of the cavity. I happened to have a perfectly sized rubber stopper on-hand so I mounted the tweeter mount to the top of the rubber stopper. This would allow me to securely mount the tweeter in the center cavity, but have it up near the top of the dashboard for the best sound.
Once I removed the OEM center speaker, I realized it was in a fairly deep hole. Tweeters sound best when they're as far up as possible so I didn't want to just set the tweeter in the bottom of the cavity. I happened to have a perfectly sized rubber stopper on-hand so I mounted the tweeter mount to the top of the rubber stopper. This would allow me to securely mount the tweeter in the center cavity, but have it up near the top of the dashboard for the best sound.
0 2017/08/31 20:41:36
Advertisement