Carrara White 991 - Mod Diary
14 Attachment(s)
Hey Guys!
7/30/2013 Finalized my transaction. Did some research here and wanted to get springs and spacers right away. 8/5/2013 Got my Carrara White delivered :) Car looked low enough; wheel gap wasn't atrocious. https://www.6speedonline.com/forums/...ine=1376711953 8/10/2013 Decided to hold off on springs and spacers. Instead went cosmetic route. Ordered: Clear Reflectors - $62.71 Clear Tail Lights - $518.95 Black Tint Film - $9.95 (I originally wanted the smoked reflector pre-cut kit, but why spend more for more work. I discovered getting an entire roll is cheaper and also easier to install.) X-ACTO Knife - $4.77 - 8/13/2013 clear reflectors arrived and installed; followed this DIY on youtube: https://www.6speedonline.com/forums/...ine=1376711953 8/15/2013 tint film arrived; followed eBay auction instructions; installed https://www.6speedonline.com/forums/...ine=1376711953 https://www.6speedonline.com/forums/...ine=1376711953 8/20/2013 Got my Clear Tail Lights today! I tried following this post for the installation. It didn't help me @_@. So here is my 991 Clear Tail Light Installation DIY ...it worked for me: Unboxed the Tail Lights https://www.6speedonline.com/forums/...ine=1377047332 Raise the Rear Spoiler. Pop up The Cap with a Flathead. Do the same for the right side. https://www.6speedonline.com/forums/...ine=1377047332 You Will Need a T25 to Unscrew These Two TorX Screws https://www.6speedonline.com/forums/...ine=1377047332 Not Enough Room for Regular ScrewDriver so I Assembled This Wrench Tool - It Did the Job https://www.6speedonline.com/forums/...ine=1377047332 After You Unscrew Both Bolts, Just Pull Tail Light Towards You and It Comes Right Off https://www.6speedonline.com/forums/...ine=1377047332 Repeat Process for Right Tail Light https://www.6speedonline.com/forums/...ine=1377047332 All Set! https://www.6speedonline.com/forums/...ine=1377047332 8/22/2013 - Polished Quad Tips ordered from Fabspeed. Got the best price direct from David@Fabspeed. 9/06/2013 Got my Fabspeed polished tips. To take off my 991 stock tips, I used an E12 reverse torx socket. You can get a set here: Alternatively:
Originally Posted by Compukidd
(Post 3931453)
...
You could have used a 10mm 6 point wrench to remove the 991 stock tip. You didnt have to spend the $ on the torx set. The Fabspeed tips use a 13mm wrench. I'm sure you know that part now. All the best! https://www.6speedonline.com/forums/...ine=1378543708 10/13/2013 Saw Brooklyn991's thread here Home Depot Plastidip - $5.95 + tax Painters Tape - $3.50 or something eBay 911 Badge - waited for my eBay bucks to kick in and got this one from the UK because the other one in the U.S.had numbers individually taped so I'd had to line it up manually. Also the UK is cheaper. https://www.6speedonline.com/forums/...ine=1381791929 https://www.6speedonline.com/forums/...ine=1381791929 |
I love your car .. color and wheels .. but I'm not entirely unbiased offcourse ;-)
https://www.6speedonline.com/forums/...0128805-30466/ |
My car is a duplicate of yours, plus I bought from PP. Who is your salesman?
Foscam cameras, I use the same, but my wap isn't in the garage. You need some of these |
Question for both of you as fellow Carrara White brothers: would you guys get Chrome or Black Chrome Quad Tips from Fabspeed? I am leaning towards Black Chrome but worried it'll just disappear under the black diffuser.
Originally Posted by bccars
(Post 3917982)
I love your car .. color and wheels .. but I'm not entirely unbiased offcourse ;-)
https://www.6speedonline.com/forums/...0128805-30466/
Originally Posted by j080808
(Post 3917997)
My car is a duplicate of yours, plus I bought from PP. Who is your salesman?
Foscam cameras, I use the same, but my wap isn't in the garage. You need some of these Amazon.com: IPCW CWB-194CA Chrome/Amber Mini Waffle Mount 194 Bulb - Pair: Automotive Ah nice, I was waiting to make use Amazon $5 of $25 Promotion. Thanks! My Sales Rep is the one and only Keith Beitter, Internet Sales Manager. If Park Place keeps it up, I'm never getting a car locally ever again; the price difference is crazy. Keith also provided great service :) |
Originally Posted by AoshichanX
(Post 3918036)
Question for both of you as fellow Carrara White brothers: would you guys get Chrome or Black Chrome Quad Tips from Fabspeed? I am leaning towards Black Chrome but worried it'll just disappear under the black diffuser.
Originally Posted by AoshichanX
(Post 3918036)
Are your wheels Platinum Satin as well? They look much darker and better on your car!
|
7 Attachment(s)
Got my Clear Tail Lights today!
I tried following this post for the installation. It didn't help me @_@. So here is my 991 Clear Tail Light Installation DIY ...it worked for me: Unboxed the Tail Lights https://www.6speedonline.com/forums/...ine=1377047332 Raise the Rear Spoiler. Pop up The Cap with a Flathead. Do the same for the right side. https://www.6speedonline.com/forums/...ine=1377047332 You Will Need a T25 to Unscrew These Two TorX Screws https://www.6speedonline.com/forums/...ine=1377047332 Not Enough Room for Regular ScrewDriver so I Assembled This Wrench Tool - It Did the Job https://www.6speedonline.com/forums/...ine=1377047332 After You Unscrew Both Bolts, Just Pull Tail Light Towards You and It Comes Right Off https://www.6speedonline.com/forums/...ine=1377047332 Repeat Process for Right Tail Light https://www.6speedonline.com/forums/...ine=1377047332 All Set! https://www.6speedonline.com/forums/...ine=1377047332 |
Do you like the clear lenses over the stock red ones on your white baby ?
|
Looking good ;) Are you also tinting the windows?
|
8/22/2013 - Polished Quad Tips ordered from Fabspeed :)
Originally Posted by bccars
(Post 3921064)
Do you like the clear lenses over the stock red ones on your white baby ?
Originally Posted by ECS Tuning - Porsche
(Post 3921188)
Looking good ;) Are you also tinting the windows?
That would set off the contrast nicely and also complement the rear tinted reflectors. But the look is a bit too aggressive for me haha. |
Looking good. A set of black wheels with a polished lip would be the perfect complement.
|
Originally Posted by AoshichanX
(Post 3918036)
My Sales Rep is the one and only Keith Beitter, Internet Sales Manager. If Park Place keeps it up, I'm never getting a car locally ever again; the price difference is crazy.
Keith also provided great service :) Beautiful car, needless to say....:) |
Love the clears--- can you disclose the price? (sorry if you did and I missed it)
Edit: I have a 4s so the center would be red still- that would look odd wouldnt it?? |
Originally Posted by Vic55
(Post 3923501)
Love the clears--- can you disclose the price? (sorry if you did and I missed it)
Edit: I have a 4s so the center would be red still- that would look odd wouldnt it?? |
Looking good.
How about front spoiler lip and Sharkwerks bypass exhaust?! |
Originally Posted by Chiboy
(Post 3923366)
Can you PM me with the % discount you received? I am going to order a lightly optioned (probably White!) 991 this winter if I can't find a good deal on a used one and would consider going outside Chicagoland if it made sense.
Beautiful car, needless to say....:)
Originally Posted by Vic55
(Post 3923501)
Love the clears--- can you disclose the price? (sorry if you did and I missed it)
Edit: I have a 4s so the center would be red still- that would look odd wouldnt it?? I did post it but no biggie at all. Here it is again (click blue link): Clear Tail Lights - $518.95 shipping included from Florida I would tint out the center red portion as well otherwise I think it would look a bit mismatched haha
Originally Posted by kosmo69
(Post 3923548)
Looking good.
How about front spoiler lip and Sharkwerks bypass exhaust?! As for the exhaust not sure about installing it on a leased car haha |
3 Attachment(s)
Got my Fabspeed polished tips.
To take off my 991 stock tips, I used an E12 reverse torx socket. You can get a set here: Alternatively:
Originally Posted by Compukidd
(Post 3931453)
...
You could have used a 10mm 6 point wrench to remove the 991 stock tip. You didnt have to spend the $ on the torx set. The Fabspeed tips use a 13mm wrench. I'm sure you know that part now. All the best! https://www.6speedonline.com/forums/...ine=1378543708 |
Good to see it finally came together. Looks gooooood !
|
can u post a few more pics of the fabspeed tips....a profile of of the back...maybe the back half of the tire showing.. and then from above.
thanks...i'm considering these tips...how do they look on person compared to the S tips? |
14 Attachment(s)
Originally Posted by bccars
(Post 3932557)
Good to see it finally came together. Looks gooooood !
Originally Posted by studlee
(Post 3933387)
can u post a few more pics of the fabspeed tips....a profile of of the back...maybe the back half of the tire showing.. and then from above.
thanks...i'm considering these tips...how do they look on person compared to the S tips? https://www.6speedonline.com/forums/...ine=1378709608 https://www.6speedonline.com/forums/...ine=1378709608 https://www.6speedonline.com/forums/...ine=1378709608 https://www.6speedonline.com/forums/...ine=1378709608 https://www.6speedonline.com/forums/...ine=1378709608 https://www.6speedonline.com/forums/...ine=1378709608 https://www.6speedonline.com/forums/...ine=1378709608 |
Looks awesome
|
3 Attachment(s)
looks familiar.
|
looks awesome....your Porsche is exactly how I configured mine, but I ended up with guard red. thanks for the pictures.
|
Your car looks awesome!
|
2 Attachment(s)
one more.
|
Originally Posted by SLATETT
(Post 3933509)
Looks awesome
Originally Posted by studlee
(Post 3933877)
looks awesome....your Porsche is exactly how I configured mine, but I ended up with guard red. thanks for the pictures.
Originally Posted by eg991
(Post 3933879)
Your car looks awesome!
Originally Posted by tanman
(Post 3933881)
one more.
|
Love the clear tails on white. Have you thought about wrapping the roof black?
|
2 Attachment(s)
Love the look of your car! It really comes together nicely! You should wrap the roof! I had mine done a couple of weeks ago and I think it came out great. Looks nice on the white with dark wheels!
https://www.6speedonline.com/forums/...ine=1379019209 https://www.6speedonline.com/forums/...ine=1379019209 |
Not sure about the roof wrap. How does it look with the sunroof open?
|
AoshichanX, very nice car. A bit biased as I also have a white 991 with the same wheels. Love your upgrades and appreciate the detail of your changes. Your diary shows the twin tip exhaust was purchased through Fabspeed. Went to their web page and I read that they will only fit an S exhaust system. But based on your post it appears it was as simple as pulling off the wide tips and reinstalling the twin tips. Is that correct? And thank you again for your post.
|
Your white car would look better with Silver wheels.
You should trade wheels with me. Those clear tails really work on your car. |
2 Attachment(s)
10/13/2013
Saw Brooklyn991's thread here Home Depot Plastidip - $5.95 + tax Painters Tape - $3.50 or something eBay 911 Badge - waited for my eBay bucks to kick in and got this one from the UK because the other one in the U.S.had numbers individually taped so I'd had to line it up manually. Also the UK is cheaper. https://www.6speedonline.com/forums/...ine=1381791990 https://www.6speedonline.com/forums/...ine=1381791990 |
Originally Posted by megmarc
(Post 3957500)
AoshichanX, very nice car. A bit biased as I also have a white 991 with the same wheels. Love your upgrades and appreciate the detail of your changes. Your diary shows the twin tip exhaust was purchased through Fabspeed. Went to their web page and I read that they will only fit an S exhaust system. But based on your post it appears it was as simple as pulling off the wide tips and reinstalling the twin tips. Is that correct? And thank you again for your post.
For the Base 991, we share the same as the 997 tips, that's what Fabspeed said. These will work for the Base 991: http://www.ebay.com/itm/Fabspeed-Por...8774ac&vxp=mtr These will work for the 991s or 991 base w/ PSE: http://www.ebay.com/itm/Fabspeed-Por...c04866&vxp=mtr I wouldn't worry about being confused by Fabspeed's website. They sent me the wrong tips twice...https://www.6speedonline.com/forums/...-fabspeed.html and yup just unscrew the original wide tips, pull off, and put the new tips in :)
Originally Posted by lunarx
(Post 3957620)
Your white car would look better with Silver wheels.
You should trade wheels with me. Those clear tails really work on your car. |
Black porsche 911 lettering is GORGEOUS !
I'm envious now ! |
Thanks for the link to the 997 tips. Love your car.
|
Originally Posted by bccars
(Post 3958214)
Black porsche 911 lettering is GORGEOUS !
I'm envious now !
Originally Posted by megmarc
(Post 3958373)
Thanks for the link to the 997 tips. Love your car.
|
16 Attachment(s)
Got my steering wheel today.
You will need:
Steps:
done... Attachment 313052 Attachment 313053 Attachment 313054 Attachment 313055 https://www.6speedonline.com/forums/...ine=1387528017 https://www.6speedonline.com/forums/...ine=1387528017 Attachment 313056 https://www.6speedonline.com/forums/...ine=1387528017 |
Great thread! Very nice mods! I too really like that black lettering! Plasti-dip FTW!! And the best thing is it just peels off when you want to change it!
What was the factory steering wheel that came with the car? Thanks! |
I thought all 2013's in White were just that "White"? Carrera White is the name of the 2012 white? Paint code on my 2013 is 0Q which is not Carrera White but just White.
|
nice write up! love your car, photos do not do it justice!
|
Just curious why you didn't order the steering wheels with the paddles at the time of purchase? Surely aftermarket on this item isn't cheaper. I replaced my steering wheel aftermarket and it was over $1,000. This option is only about $500 at time of purchase.
|
All times are GMT -6. The time now is 02:24 PM. |
© 2024 MH Sub I, LLC dba Internet Brands