My 2010 Audi S4 - Daily Driver
Thread Starter
|
Former Vendor
Joined: Aug 2005
Posts: 2,888
From: New Jersey
Rep Power: 0
My 2010 Audi S4 - Daily Driver
2010 Phantom Black/Black with Silver inserts
This was a new car prep that required clay and PO85RD, we finished with Collinite and Swissvax Divine. (unfortunately the car will be sitting outside for most of its life)
We also wrapped the front clip with 3m PPF.
Products used:
Exterior:
Lusso AutoBathe
Uber Boar's Hair Wash Brush 7 inch
Swissvax Yellow Clay Bar and Optimum Instant Detail Spray and Gloss Enhancer
Einszett Spray Wax
P21S Finish Restorer Metal Polish (on the tips)
Menzerna PO85RD
Collinite Insulator Wax
Swissvax Divine
Wheels and tires:
P21S Wheel Cleaner Gel
Swissvax Wheel Brush
Uber Wheel Brush
Uber Spoke Brush
Swissvax Pneu
Swissvax Autobahn
Tools:
Infratech 5300
Flex 3403
The Uber Foam Pads (5.5inch)
Tons of "Uber" Microfiber Towels
Uber Drying Towels
Brushes
Gilmour Foam Gun
To the pics:
Before:
Dirty Wheels
Wash
Tom on the foam gun
Wheels being worked on
Debadged:
Tagged:
Engine shot:
interior shots:
Rear bumper film install (just partially installed to protect the top)
Polished
Front end install:
Final shots:
This was a new car prep that required clay and PO85RD, we finished with Collinite and Swissvax Divine. (unfortunately the car will be sitting outside for most of its life)
We also wrapped the front clip with 3m PPF.
Products used:
Exterior:
Lusso AutoBathe
Uber Boar's Hair Wash Brush 7 inch
Swissvax Yellow Clay Bar and Optimum Instant Detail Spray and Gloss Enhancer
Einszett Spray Wax
P21S Finish Restorer Metal Polish (on the tips)
Menzerna PO85RD
Collinite Insulator Wax
Swissvax Divine
Wheels and tires:
P21S Wheel Cleaner Gel
Swissvax Wheel Brush
Uber Wheel Brush
Uber Spoke Brush
Swissvax Pneu
Swissvax Autobahn
Tools:
Infratech 5300
Flex 3403
The Uber Foam Pads (5.5inch)
Tons of "Uber" Microfiber Towels
Uber Drying Towels
Brushes
Gilmour Foam Gun
To the pics:
Before:
Dirty Wheels
Wash
Tom on the foam gun
Wheels being worked on
Debadged:
Tagged:
Engine shot:
interior shots:
Rear bumper film install (just partially installed to protect the top)
Polished
Front end install:
Final shots:
Thread Starter
|
Former Vendor
Joined: Aug 2005
Posts: 2,888
From: New Jersey
Rep Power: 0
Well I'm starting to personalize the Audi a bit.
First up on the mods Bilstein PSS10's
I was pretty skeptical at first as I had PSS9's on my 03 Audi RS6 I would have probably preferred KW's on that one, took the leap on the PSS10's and have to say I'm extremely happy with the decision to go with the PSS10's on the B8 S4.
Take a look.
The PSS10's:
Fronts out
The dial is a huge improvement over the PSS9's
The fronts are in (just about)
Front of car after we dropped the car off the lift (definitely too low)
Before rear (sorry pretty bad shots)
After rear (sorry pretty bad shots)
Before fronts
After fronts
After a few miles the car settled and we had to adjust it a few times to get it right, I experienced some rubbing with 3 in the car so we raised it and took the front wheel liner bolt off.
First up on the mods Bilstein PSS10's
I was pretty skeptical at first as I had PSS9's on my 03 Audi RS6 I would have probably preferred KW's on that one, took the leap on the PSS10's and have to say I'm extremely happy with the decision to go with the PSS10's on the B8 S4.
Take a look.
The PSS10's:
Fronts out
The dial is a huge improvement over the PSS9's
The fronts are in (just about)
Front of car after we dropped the car off the lift (definitely too low)
Before rear (sorry pretty bad shots)
After rear (sorry pretty bad shots)
Before fronts
After fronts
After a few miles the car settled and we had to adjust it a few times to get it right, I experienced some rubbing with 3 in the car so we raised it and took the front wheel liner bolt off.
Thread Starter
|
Former Vendor
Joined: Aug 2005
Posts: 2,888
From: New Jersey
Rep Power: 0
After shot with final adjustments and Menzerna Power Lock
Thanks Drive Auto Works in Lydnhurst, NJ
Next up
RS6 Pedals from Alex at EuroPrice
Before and After
a couple more pics of the drop.
Finally got a chance to install my RS6 Euro wheel in. Take a look
Before
After
Wheels - BBS LM-R 19's
Teaser pics - Iphone shots more to come.
5mm eibach spacers on (they have since been removed)
Thanks Drive Auto Works in Lydnhurst, NJ
Next up
RS6 Pedals from Alex at EuroPrice
Before and After
a couple more pics of the drop.
Finally got a chance to install my RS6 Euro wheel in. Take a look
Before
After
Wheels - BBS LM-R 19's
Teaser pics - Iphone shots more to come.
5mm eibach spacers on (they have since been removed)
Thread Starter
|
Former Vendor
Joined: Aug 2005
Posts: 2,888
From: New Jersey
Rep Power: 0
Updated pic
So I dropped the car and its looking pretty good, I may drop it a bit more...not sure...pics to come.
Installed the AWE Boost Gauge Super Nice Piece.
Before
Great looking piece
After
a few more goodies...
Supercharged Badges
3m adhesive remover to prep the area
Template in place
Supercharged Badge in place
And the finish
AWE Tuning Resonated DP and Exhaust Installed (More Pics to come on this mod)
Not my car but this is what it sounds like
<object width="480" height="385"><param name="movie" value="http://www.youtube.com/v/okJ92c_V7Lw&hl=en_US&fs=1"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/okJ92c_V7Lw&hl=en_US&fs=1" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="480" height="385"></embed></object>
BIG BRAKES!
Stoptech ST-60's (380mm) installed.
Stock Rotor
Stoptech Rotor
Out of the box
Stock brakes
Stoptechs on the car
on the ground
Registered User
Joined: May 2007
Posts: 147
From: Australia
Rep Power: 24
Wow well done. You've made some simple yet very effective mods to an already great looking car. Looks awesome!
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
