Another Round of mods (rods and goodies)
Thread Starter
|
Registered User
Joined: May 2012
Posts: 677
From: Coppell, TX USA
Rep Power: 113
heads are going. been trying to knock out one cyl per night after work. Here are some rough in, to 80% complete (final sanding not complete until all 24 ports are measured and reasonably the same).
This is a very mild port, focusing on the normal pinch points.
This is a very mild port, focusing on the normal pinch points.
Registered User
Joined: Oct 2014
Posts: 331
Rep Power: 65
This was sour prototype, inserts remain the same, from right to left, locating pin, drill bushing, tap bushing, drill bushing (2)
We still recommend having the liner case and heads drilled on a bridgeport for accuracy but the case part is very easy with this tool.
Registered User
Joined: Jan 2014
Posts: 379
From: Canada
Rep Power: 100
I'll be posting a step by step 2 weeks from now when I re assemble my bottom end. There is an order for it to be done.
Thread Starter
|
Registered User
Joined: May 2012
Posts: 677
From: Coppell, TX USA
Rep Power: 113
VR- thanks.. ya i knew it was a challenge, just didnt know how much of one!
If there are any references out there, please post.. thanks. Going to try to mess with it a little tonight.. maybe
If there are any references out there, please post.. thanks. Going to try to mess with it a little tonight.. maybe
Last edited by jordonmusser; Jan 4, 2016 at 04:09 PM.
Registered User
Joined: Oct 2015
Posts: 66
Rep Power: 18
I like the direction in this build. Good luck and looking forward to your updates. Please don't go quiet on us when its complete!
For me its either going all out with displacement or do just the very basics like this which carries the least cost and risk of all options. Anything in between to me personally is meh as then it just adds up very quickly and you end up wishing you did more while you were in there at least it does/would in my case.
For me its either going all out with displacement or do just the very basics like this which carries the least cost and risk of all options. Anything in between to me personally is meh as then it just adds up very quickly and you end up wishing you did more while you were in there at least it does/would in my case.
__________________
#TeamAIM
997TT SilverSpool - 210.8 mph 1/2 Mile WR Apr 2019, 9.2 @ 168 mph 1/4 Mile Manual World Record , 3.15 60-130 mph , 2.72 100-150 mph , 1400whp E85
996TT SpoolBus - 204.6 mph 1/2 Mile 996TT WR Aug 2018, 9.5 @ 154 mph, 3.23 60-130 mph, 2.5 100-150 mph Manual Porsche World Record, 1400whp E85
997TT SlowBerry - 205.0 mph 1/2 Mile WR Nov 2018, 9.7 @ 170 mph 1/4 Mile , 3.2 60-130 mph , 2.4 100-150 mph , 1420whp E85
ESMOTOR | DO88 | TPC DSC | SYVECS | COBB | IPD | KLINE | XONA | AMS | ID | ERP | SACHS | TURBOSMART | CSF | DODSON |
#TeamAIM
997TT SilverSpool - 210.8 mph 1/2 Mile WR Apr 2019, 9.2 @ 168 mph 1/4 Mile Manual World Record , 3.15 60-130 mph , 2.72 100-150 mph , 1400whp E85
996TT SpoolBus - 204.6 mph 1/2 Mile 996TT WR Aug 2018, 9.5 @ 154 mph, 3.23 60-130 mph, 2.5 100-150 mph Manual Porsche World Record, 1400whp E85
997TT SlowBerry - 205.0 mph 1/2 Mile WR Nov 2018, 9.7 @ 170 mph 1/4 Mile , 3.2 60-130 mph , 2.4 100-150 mph , 1420whp E85
ESMOTOR | DO88 | TPC DSC | SYVECS | COBB | IPD | KLINE | XONA | AMS | ID | ERP | SACHS | TURBOSMART | CSF | DODSON |
Premium Sponsor
Joined: May 2006
Posts: 922
Rep Power: 90
Just to let everyone know we also sell the rings separately if you need them.
They are our part # 100 103 102 01
They are our part # 100 103 102 01
__________________
FVD Brombacher - USA
Contact me directly to get the latest FVD forum member discount!
Rhonda Roxburgh
+1-954-571-2050 x 1
rhonda.roxburgh@fvd.net
Visit our online shop for an extensive selection of tuning and original parts www.fvd.net
FVD Brombacher - USA
Contact me directly to get the latest FVD forum member discount!
Rhonda Roxburgh
+1-954-571-2050 x 1
rhonda.roxburgh@fvd.net
Visit our online shop for an extensive selection of tuning and original parts www.fvd.net