Stuffed Bose Subwoofer
Stuffed Bose Subwoofer
My wife donated this pillow to be sacrificed for the mod. Very easy to do. Removed port to stuff box pretty full then re-installed. Sounds real nice, a noticeable improvement but the bass had to be adjusted; turned it up a bit because it was tighter but quieter. Great info on this board and planet9 about the install.
Hmmm, interesting. Thanks for sharing. More details or a link please.
Anyone else try this yet and what are your perceptions?
The Bose box does get pretty boomy especially top down at hwy speeds.
Thanks!
Anyone else try this yet and what are your perceptions?
The Bose box does get pretty boomy especially top down at hwy speeds.
Thanks!
Trending Topics
Hahahaha, Bravo.
__________________
damon@tirerack.com
877-522-8473 ext. 4643
574-287-2345 ext. 4643
**Don't forget to add my name to online orders!**
Or use this link:
http://www.tirerack.com/a.jsp?a=BH1&url=index.jsp
damon@tirerack.com
877-522-8473 ext. 4643
574-287-2345 ext. 4643
**Don't forget to add my name to online orders!**
Or use this link:
http://www.tirerack.com/a.jsp?a=BH1&url=index.jsp
Good info
some more relevant info on stuffing here - http://www.moodym.com/audio/fiber.html
and Acousta-Stuf superior material for stuffing here -
http://www.parts-express.com/pe/show...number=260-317
some more relevant info on stuffing here - http://www.moodym.com/audio/fiber.html
and Acousta-Stuf superior material for stuffing here -
http://www.parts-express.com/pe/show...number=260-317
Just a quick follow up here, I took it a step further. Picked up the smallest bag of poly-fil at JoAnn Fabrics for $2.99 (still have 3/4 of the bag left too...) - no it's not N-spec 
Anyhow, instead of trying stuff the filler in thru the port, just unscrew the 6 (IIRC) torx screws holding the driver and grill in/onto the bottom of the box. No need to disco the wires to the driver, just lift it out of the enclosure and place to the side. Then using your hands, stuff the poly-fil in from here into all the corners, crevices and open space in the box. Firmly but loose I think is the technical measurement
. Then just replace the driver, grill and 6 torx screws into the enclosure and reinstall the enclosure back into vehicle.
Very noticeable difference in the subs response - a little deeper but much tighter eliminating a lot of the boomy-ness especially top down.
Excellent mod for $2.99 and 15 min.
Thanks again Gator Skin for posting and the link

Anyhow, instead of trying stuff the filler in thru the port, just unscrew the 6 (IIRC) torx screws holding the driver and grill in/onto the bottom of the box. No need to disco the wires to the driver, just lift it out of the enclosure and place to the side. Then using your hands, stuff the poly-fil in from here into all the corners, crevices and open space in the box. Firmly but loose I think is the technical measurement
. Then just replace the driver, grill and 6 torx screws into the enclosure and reinstall the enclosure back into vehicle.Very noticeable difference in the subs response - a little deeper but much tighter eliminating a lot of the boomy-ness especially top down.
Excellent mod for $2.99 and 15 min.
Thanks again Gator Skin for posting and the link
Last edited by Burg Boxster; Jun 23, 2010 at 03:10 PM.
Have done the same - followed the mod instructions on the planet-9.
Works amazing well - bass is MUCH tighter and "punchier" especially in my cab.
Thanks for highlighting this one.
Gundo
Works amazing well - bass is MUCH tighter and "punchier" especially in my cab.
Thanks for highlighting this one.
Gundo
Thanks for the post. I have been on this forum for a while but have never posted anything. This mod was so great I had to post something and thank you guys.
Thanks for the tip and a wonderful forum!
Thanks for the tip and a wonderful forum!




